Water hardness in Kitsap County, WA

Water in Kitsap County is moderately hard, with a median of 88 mg/L (5.1 grains per gallon) across 74 monitoring sites.

19% harder than the Washington median (74 mg/L) 14th hardest of 35 counties
88mg/L
5.1 grains per gallon
Moderately hard

Kitsap County water at a glance

  • HardnessModerately hard (88 mg/L, 5.1 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
  • Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →

What 88 mg/L means at home

  • Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
  • Dishwasher: set the water hardness to about 5.1 gpg (4.9 °dH), which is a low-to-medium hardness setting.
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites74
Lab samples99
Sample years2000–2021
Middle 50% of sites63–152 mg/L
Groundwater (wells, springs)106 mg/L · 63 sites
Surface water (rivers, lakes)45 mg/L · 11 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Kitsap County

Prefilled with Kitsap County's measured local hardness of 88 mg/L (5.1 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

Kitsap County on the Washington map

King CountyLincoln CountyPend Oreille CountyAsotin CountySkagit CountyFranklin CountyWhitman CountyYakima CountyClark CountyBenton CountyKittitas CountyWahkiakum CountyIsland CountyClallam CountyGrays Harbor CountyPacific CountySan Juan CountySpokane CountyWhatcom CountyDouglas CountyGrant CountySnohomish CountyOkanogan CountyFerry CountyCowlitz CountyMason CountyColumbia CountyAdams CountySkamania CountyJefferson CountyWalla Walla CountyPierce CountyChelan CountyGarfield CountyThurston CountyKlickitat CountyLewis CountyStevens County

Cities and communities in Kitsap County

PlaceMedian mg/LClassBased on
Bremerton 66 Moderately hard 32 sites within 10 miles
Bainbridge Island 106 Moderately hard 45 sites within 10 miles
Silverdale (CDP) 98 Moderately hard 68 sites within 10 miles
Port Orchard 70 Moderately hard 29 sites within 10 miles
Poulsbo 89 Moderately hard 55 sites within 10 miles
Parkwood (CDP) 72 Moderately hard 27 sites within 10 miles
Bangor Base (CDP) 89 Moderately hard 55 sites within 10 miles
East Port Orchard (CDP) 71 Moderately hard 28 sites within 10 miles
Manchester (CDP) 78 Moderately hard 25 sites within 10 miles
Tracyton (CDP) 84 Moderately hard 53 sites within 10 miles
Suquamish (CDP) 93 Moderately hard 54 sites within 10 miles
Bethel (CDP) 63 Moderately hard 24 sites within 10 miles
Indianola (CDP) 101 Moderately hard 54 sites within 10 miles
Hansville (CDP) 88 Moderately hard county median
Navy Yard City (CDP) 70 Moderately hard 36 sites within 10 miles
Lofall (CDP) 106 Moderately hard 46 sites within 10 miles
Enetai (CDP) 87 Moderately hard 50 sites within 10 miles
Chico (CDP) 88 Moderately hard 73 sites within 10 miles
Southworth (CDP) 81 Moderately hard 22 sites within 10 miles
Kingston (CDP) 106 Moderately hard 48 sites within 10 miles
Burley (CDP) 61 Moderately hard 26 sites within 10 miles
Rocky Point (CDP) 84 Moderately hard 53 sites within 10 miles
Seabeck (CDP) 102 Moderately hard 63 sites within 10 miles
Port Gamble Tribal Community (CDP) 96 Moderately hard 23 sites within 10 miles
Gorst (CDP) 59 Soft 34 sites within 10 miles
Keyport (CDP) 89 Moderately hard 55 sites within 10 miles
Erlands Point (CDP) 84 Moderately hard 53 sites within 10 miles
Kitsap Lake (CDP) 83 Moderately hard 55 sites within 10 miles

Water quality in Kitsap County communities

Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology

CommunityWater systemPFASLead linesViolations
Bremerton City of Bremerton 1 found 0 lead · 0 unknown None
Bainbridge Island City of Bainbridge Island None detected 0 lead · 2,307 unknown None
Silverdale Silverdale Water Dist 16 None detected 0 lead · 29 unknown None
Port Orchard Port Orchard Water None detected Not reported None
Poulsbo City of Poulsbo None detected 0 lead · 0 unknown None
Parkwood Parkwood Not tested 0 lead · 0 unknown 3
Manchester Manchester Water District None detected 0 lead · 0 unknown None
Suquamish Suquamish None detected 427 lead · 0 unknown None
Bethel Bethel Water Not tested Not reported None
Indianola Indianola Water Not tested 0 lead · 0 unknown None
Lofall Lofall Water System INC Not tested Not reported None
Seabeck Seabeck None detected Not reported None
Keyport Keyport Water Not tested 0 lead · 0 unknown None

Neighboring counties

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next