Water hardness in Benton County, WA
Water in Benton County is moderately hard, with a median of 67 mg/L (3.9 grains per gallon) across 10 monitoring sites.
Benton County water at a glance
- HardnessModerately hard (67 mg/L, 3.9 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 67 mg/L means at home
- Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
- Dishwasher: set the water hardness to about 3.9 gpg (3.8 °dH), which is a low-to-medium hardness setting.
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Benton County
Prefilled with Benton County's measured local hardness of 67 mg/L (3.9 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Benton County on the Washington map
Cities and communities in Benton County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Kennewick | 134 | Hard | 6 sites within 10 miles |
| Richland | 220 | Very hard | 12 sites within 10 miles |
| West Richland | 87 | Moderately hard | 8 sites within 10 miles |
| Prosser | 86 | Moderately hard | 5 sites within 10 miles |
| Finley (CDP) | 243 | Very hard | 4 sites within 10 miles |
| Benton City | 82 | Moderately hard | 5 sites within 10 miles |
Water quality in Benton County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Kennewick | City of Kennewick | 6 found (PFOA 4.6 / PFOS 11.5 ppt) | 0 lead · 0 unknown | None |
| Richland | City of Richland | 8 found (PFOA 10.1 / PFOS 17 ppt) | Not reported | None |
| West Richland | City of West Richland | None detected | 0 lead · 0 unknown | None |
| Prosser | City of Prosser | None detected | 0 lead · 97 unknown | None |
| Benton City | Benton City Water | 6 found (PFOA ND / PFOS 8.7 ppt) | 0 lead · 398 unknown | None |
Neighboring counties
- Franklin County240 mg/L
- Walla Walla County66 mg/L
- Yakima County178 mg/L
- Klickitat County63 mg/L
- Grant County176 mg/L
- Adams County233 mg/L
Washington
The statewide median is 74 mg/L (moderately hard) from 890 sites.
Washington hardness map →Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.