Water hardness in Silverdale, WA

Water in Silverdale is moderately hard, with a median of 98 mg/L (5.7 grains per gallon) across 68 monitoring sites within 10 miles.

32% harder than the Washington median (74 mg/L) 17th hardest of 122 Washington towns Population 19,204 (2010)
98mg/L
5.7 grains per gallon
Moderately hard

Silverdale tap water at a glance

  • HardnessModerately hard (98 mg/L, 5.7 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
  • PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
  • Lead pipesNo known lead lines; 29 lines are still of unknown material.Check your own pipe →
  • ViolationsNo health-based violations since 2016.EPA record →

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 98 mg/L means at home

  • Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
  • Dishwasher: set the water hardness to about 5.7 gpg (5.5 °dH), which is a low-to-medium hardness setting.
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites68
Lab samples83
Sample years2000–2021
Middle 50% of sites70–163 mg/L
Groundwater (wells, springs)106 mg/L · 61 sites
Surface water (rivers, lakes)59 mg/L · 7 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Silverdale

Prefilled with Silverdale's measured local hardness of 98 mg/L (5.7 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Silverdale tap water

Silverdale Water Dist 16 is the main public water system for Silverdale. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 20 samples taken Apr 2024 – Jul 2025. No PFAS were found at or above EPA's minimum reporting levels.

Other water systems serving parts of Silverdale

Water systemPFAS detectedHighest PFOA / PFOSTested
City of Bremerton
serves over 10,000 people
PFBS — Jul 2024 – Apr 2025
North Perry Ave Water District
serves over 10,000 people
None detected — Oct 2023 – Apr 2024
North Peninsula
serves over 10,000 people
None detected — Aug 2025 – Oct 2025
City of Poulsbo
serves over 10,000 people
None detected — Oct 2024 – Apr 2025

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Silverdale

Silverdale Water Dist 16 reported 475 service lines (the pipes connecting homes to the water main) in its inventory. It reported no known lead lines, but 29 lines are still of unknown material.

0lead (0%)
0galvanized requiring replacement
29unknown material (6%)
446not lead (94%)

Other water systems serving parts of Silverdale

Water systemService linesTotal
City of Bremerton0 lead · 0 galvanized · 0 unknown20,315
North Perry Ave Water District0 lead · 240 galvanized · 3,614 unknown6,986
North PeninsulaNot reported—
City of Poulsbo0 lead · 0 galvanized · 0 unknown4,077

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Silverdale drinking water violations

EPA records show no health-based violations for Silverdale Water Dist 16 since 2016. It also had 1 monitoring or reporting violation (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.

Other water systems serving parts of Silverdale

Water systemHealth-based violationsMonitoring/reporting
City of BremertonNone2
North Perry Ave Water DistrictNone0
North PeninsulaNone1
City of PoulsboNone5

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Silverdale

SiteTypeDistanceMedianSamplesYears
25N/01E-14Q03
USGS Washington Water Science Center
Well 2.3 mi86 mg/L12008
25N/01E-02J03
USGS Washington Water Science Center
Well 2.5 mi76 mg/L12008
26N/01E-32E07 (F-MW23)
USGS Washington Water Science Center
Well 2.7 mi160 mg/L12001
26N/01E-36N17 MW1-33
USGS Washington Water Science Center
Well 3.2 mi60 mg/L12000
25N/01E-26B02
USGS Washington Water Science Center
Well 3.2 mi84 mg/L12008
26N/01E-31B07 (F-MW39)
USGS Washington Water Science Center
Well 3.2 mi88 mg/L12001

Water hardness in towns near Silverdale

TownDistanceMedianClass
Poulsbo5 mi 89 mg/LModerately hard
Bainbridge Island8 mi 106 mg/LModerately hard
Bremerton9 mi 66 mg/LModerately hard
Port Orchard9 mi 70 mg/LModerately hard
Seattle16 mi 28 mg/LSoft
Shoreline17 mi 98 mg/LModerately hard
Edmonds18 mi 98 mg/LModerately hard
White Center19 mi 67 mg/LModerately hard
Lake Forest Park19 mi 93 mg/LModerately hard
Mountlake Terrace20 mi 98 mg/LModerately hard

Kitsap County

Silverdale is in Kitsap County, where the median is 88 mg/L (moderately hard) across 74 sites.

See all of Kitsap County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Silverdale, WA water: common questions

Do I need a water softener in Silverdale?

Probably not. Water measured around Silverdale is 5.7 gpg (98 mg/L, measured locally), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable. If spotting bothers you, about 10,000 grains of capacity covers a 3-person home between weekly regenerations.Size it for your household →

Who supplies Silverdale's drinking water?

The main public water system serving Silverdale in EPA records is Silverdale Water Dist 16. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Silverdale?

Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next