Water hardness in Seattle, WA
Tap water in Seattle is soft: about 28 mg/L (1.6 grains per gallon), ranging from 27 to 30 mg/L, as reported by Seattle Public Utilities.
Utility-reported value. May 2026 quarterly analysis of Cedar River supply: 1.55 to 1.73 grains per gallon. Source: Seattle Public Utilities (2026). Local groundwater and surface water around Seattle measures harder (median 103 mg/L), which matters if you are on a private well.
Seattle tap water at a glance
- HardnessSoft (28 mg/L, 1.6 gpg, utility report). A water softener isn't needed.Water heater care →
- PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
- Lead pipesNo lead service lines reported.Details →
- ViolationsNo health-based violations since 2016.EPA record →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 28 mg/L means at home
- Water softener: A water softener is generally not needed. Soft water rarely causes scale.
- Dishwasher: set the water hardness to about 1.6 gpg (1.6 °dH), which is the lowest hardness setting (or softener off).
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Local source water measurements
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Seattle
Prefilled with Seattle's utility-reported hardness of 28 mg/L (1.6 gpg).
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Seattle tap water
Seattle Public Utilities is the main public water system for Seattle. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 8 samples taken Jun 2023 – Dec 2023. No PFAS were found at or above EPA's minimum reporting levels.
Other water systems serving parts of Seattle
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| Tukwila Water Department serves over 10,000 people | None detected | — | Mar 2024 – Dec 2024 |
| King County Water District #20 serves over 10,000 people | None detected | — | Mar 2024 – Dec 2024 |
| Skyway Water & Sewer serves over 10,000 people | None detected | — | May 2023 – Feb 2024 |
| North City Water District serves over 10,000 people | None detected | — | Jul 2024 – Apr 2025 |
| Northshore Utility District serves over 10,000 people | None detected | — | Mar 2023 – Dec 2023 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Seattle
Seattle Public Utilities reported 206,340 service lines (the pipes connecting homes to the water main) in its inventory. It reported no lead or galvanized lines requiring replacement.
Other water systems serving parts of Seattle
| Water system | Service lines | Total |
|---|---|---|
| Tukwila Water Department | 0 lead · 0 galvanized · 2,110 unknown | 2,401 |
| King County Water District #20 | 0 lead · 141 galvanized · 0 unknown | 10,748 |
| Skyway Water & Sewer | 0 lead · 0 galvanized · 3,435 unknown | 3,435 |
| North City Water District | 0 lead · 459 galvanized · 41 unknown | 8,138 |
| Northshore Utility District | 0 lead · 0 galvanized · 2,001 unknown | 22,883 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Seattle drinking water violations
EPA records show no health-based violations for Seattle Public Utilities since 2016.
Other water systems serving parts of Seattle
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| Tukwila Water Department | None | 0 |
| King County Water District #20 | None | 0 |
| Skyway Water & Sewer | None | 2 |
| North City Water District | None | 0 |
| Northshore Utility District | None | 0 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Seattle
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| LONGFELLOW CREEK AB GENESEE ST NR WEST SEATTLE, WA USGS Washington Water Science Center | Stream | 3.9 mi | 142 mg/L | 10 | 2015 |
| THORNTON CREEK NEAR SEATTLE, WA USGS Washington Water Science Center | Stream | 6.3 mi | 103 mg/L | 19 | 2001–2015 |
| PIPERS CREEK AT CARKEEK PARK, AT SEATTLE, WA USGS Washington Water Science Center | Stream | 6.5 mi | 116 mg/L | 10 | 2015 |
| MERCER CREEK NEAR BELLEVUE, WA USGS Washington Water Science Center | Stream | 8 mi | 110 mg/L | 10 | 2015 |
| COAL CREEK AT BELLEVUE, WA USGS Washington Water Science Center | Stream | 8.6 mi | 162 mg/L | 10 | 2015 |
| JUANITA CREEK NEAR KIRKLAND, WA USGS Washington Water Science Center | Stream | 8.8 mi | 93 mg/L | 10 | 2015 |
Water hardness in towns near Seattle
| Town | Distance | Median | Class |
|---|---|---|---|
| Mercer Island | 7 mi | 80 mg/L | Moderately hard |
| Bainbridge Island | 7 mi | 106 mg/L | Moderately hard |
| White Center | 8 mi | 67 mg/L | Moderately hard |
| Kirkland | 9 mi | 93 mg/L | Moderately hard |
| Bellevue | 9 mi | 71 mg/L | Moderately hard |
| Shoreline | 10 mi | 98 mg/L | Moderately hard |
| Burien | 10 mi | 70 mg/L | Moderately hard |
| Bryn Mawr-Skyway | 10 mi | 87 mg/L | Moderately hard |
| Lake Forest Park | 10 mi | 93 mg/L | Moderately hard |
| Kenmore | 10 mi | 91 mg/L | Moderately hard |
King County
Seattle is in King County, where the median is 61 mg/L (moderately hard) across 34 sites.
See all of King County →Washington
The statewide median is 74 mg/L (moderately hard) from 890 sites.
Washington hardness map →Seattle, WA water: common questions
Do I need a water softener in Seattle?
Probably not. Seattle's tap water is 1.6 gpg (28 mg/L, utility-reported), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable.When a softener helps →
Who supplies Seattle's drinking water?
The main public water system serving Seattle in EPA records is Seattle Public Utilities. Some neighborhoods may be served by a different system, so check the name on your water bill.Seattle Public Utilities water quality report →
Do I need a water filter in Seattle?
Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →
Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.