Water hardness in Bellevue, WA
Water in Bellevue is moderately hard, with a median of 71 mg/L (4.1 grains per gallon) across 13 monitoring sites within 10 miles.
Large city utilities sometimes soften, blend or import water from distant reservoirs, so tap water in Bellevue can differ from local source water. Your utility's annual Consumer Confidence Report lists the exact tap value.
Bellevue tap water at a glance
- HardnessModerately hard (71 mg/L, 4.1 gpg, local measurements). Some scale; descale kettles and flush the water heater.Water heater care →
- PFASNone found in EPA's nationwide testing of the main water system.PFAS results →
- Lead pipesNo known lead lines; 9,739 lines are still of unknown material.Check your own pipe →
- ViolationsNo health-based violations since 2016.EPA record →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 71 mg/L means at home
- Water softener: Most homes do not need a softener. You may notice light spotting on glass and fixtures.
- Dishwasher: set the water hardness to about 4.1 gpg (4 °dH), which is a low-to-medium hardness setting.
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Bellevue
Prefilled with Bellevue's measured local hardness of 71 mg/L (4.2 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Bellevue tap water
City of Bellevue is the main public water system for Bellevue. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 8 samples taken Jan 2024 – Oct 2024. No PFAS were found at or above EPA's minimum reporting levels.
Other water systems serving parts of Bellevue
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| King County Water District No 90 serves over 10,000 people | None detected | — | Sep 2024 – Jun 2025 |
| Issaquah Water System serves over 10,000 people | None detected | — | Sep 2024 – Jun 2025 |
| Woodinville Water District serves over 10,000 people | None detected | — | Sep 2024 – Jun 2025 |
| Coal Creek Utility District serves over 10,000 people | None detected | — | Jan 2024 – Oct 2024 |
| City of Kirkland serves over 10,000 people | None detected | — | Sep 2024 – Jun 2025 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Bellevue
City of Bellevue reported 40,476 service lines (the pipes connecting homes to the water main) in its inventory. It reported no known lead lines, but 9,739 lines are still of unknown material.
Other water systems serving parts of Bellevue
| Water system | Service lines | Total |
|---|---|---|
| King County Water District No 90 | 0 lead · 0 galvanized · 323 unknown | 8,198 |
| Issaquah Water System | 0 lead · 0 galvanized · 0 unknown | 9,402 |
| Woodinville Water District | 0 lead · 0 galvanized · 0 unknown | 14,831 |
| Coal Creek Utility District | 0 lead · 0 galvanized · 0 unknown | 3,991 |
| City of Kirkland | 0 lead · 82 galvanized · 0 unknown | 13,332 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Bellevue drinking water violations
EPA records show no health-based violations for City of Bellevue since 2016.
Other water systems serving parts of Bellevue
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| King County Water District No 90 | None | 2 |
| Issaquah Water System | None | 0 |
| Woodinville Water District | None | 0 |
| Coal Creek Utility District | None | 1 |
| City of Kirkland | None | 0 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Bellevue
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| MERCER CREEK NEAR BELLEVUE, WA USGS Washington Water Science Center | Stream | 1.2 mi | 110 mg/L | 10 | 2015 |
| COAL CREEK AT BELLEVUE, WA USGS Washington Water Science Center | Stream | 2.4 mi | 162 mg/L | 10 | 2015 |
| MAY CREEK BELOW HONEY DEW CREEK NEAR RENTON, WA USGS Washington Water Science Center | Stream | 5.7 mi | 78 mg/L | 10 | 2015 |
| BEAR CREEK AT UNION HILL RD AT REDMOND, WA USGS Washington Water Science Center | Stream | 5.8 mi | 65 mg/L | 10 | 2015 |
| NORTH FORK ISSAQUAH CREEK AT ISSAQUAH, WA USGS Washington Water Science Center | Stream | 6.8 mi | 82 mg/L | 10 | 2015 |
| E FORK ISSAQUAH CR ABV 3RD AVE NE AT ISSAQUAH, WA USGS Washington Water Science Center | Stream | 7.4 mi | 45 mg/L | 10 | 2015 |
Water hardness in towns near Bellevue
| Town | Distance | Median | Class |
|---|---|---|---|
| Mercer Island | 4 mi | 80 mg/L | Moderately hard |
| Newcastle | 5 mi | 65 mg/L | Moderately hard |
| Sammamish | 6 mi | 70 mg/L | Moderately hard |
| Redmond | 6 mi | 73 mg/L | Moderately hard |
| Issaquah | 6 mi | 65 mg/L | Moderately hard |
| Kirkland | 7 mi | 93 mg/L | Moderately hard |
| Bryn Mawr-Skyway | 8 mi | 87 mg/L | Moderately hard |
| Renton | 8 mi | 56 mg/L | Soft |
| Union Hill-Novelty Hill | 9 mi | 70 mg/L | Moderately hard |
| East Renton Highlands | 9 mi | 52 mg/L | Soft |
King County
Bellevue is in King County, where the median is 61 mg/L (moderately hard) across 34 sites.
See all of King County →Washington
The statewide median is 74 mg/L (moderately hard) from 890 sites.
Washington hardness map →Bellevue, WA water: common questions
Do I need a water softener in Bellevue?
Probably not. Water measured around Bellevue is 4.1 gpg (71 mg/L, measured locally), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable. If spotting bothers you, about 8,000 grains of capacity covers a 3-person home between weekly regenerations.Size it for your household →
Who supplies Bellevue's drinking water?
The main public water system serving Bellevue in EPA records is City of Bellevue. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →
Do I need a water filter in Bellevue?
Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →
Hardness scale
What to read next
- How to tell if your home has a lead pipe9,739 service lines here are of unknown material.
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.