Water hardness in Columbus County, NC
Water in Columbus County is soft, with a median of 21 mg/L (1.2 grains per gallon) across 15 monitoring sites.
Columbus County water at a glance
- HardnessSoft (21 mg/L, 1.2 gpg, local measurements). A water softener isn't needed.Water heater care →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 21 mg/L means at home
- Water softener: A water softener is generally not needed. Soft water rarely causes scale.
- Dishwasher: set the water hardness to about 1.2 gpg (1.2 °dH), which is the lowest hardness setting (or softener off).
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Columbus County
Prefilled with Columbus County's measured local hardness of 21 mg/L (1.2 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Columbus County on the North Carolina map
Cities and communities in Columbus County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Whiteville | 51 | Soft | 3 sites within 10 miles |
| Tabor City | 21 | Soft | county median |
| Chadbourn | 21 | Soft | county median |
| Lake Waccamaw | 21 | Soft | 3 sites within 10 miles |
| Brunswick | 21 | Soft | county median |
| Fair Bluff | 17 | Soft | 6 sites within 10 miles |
| Riegelwood (CDP) | 25 | Soft | 12 sites within 10 miles |
| Hallsboro (CDP) | 21 | Soft | 3 sites within 10 miles |
| Sandyfield | 27 | Soft | 8 sites within 10 miles |
| Evergreen (CDP) | 16 | Soft | 6 sites within 10 miles |
| Bolton | 22 | Soft | 6 sites within 10 miles |
| Delco (CDP) | 26 | Soft | 11 sites within 10 miles |
| Boardman | 16 | Soft | 10 sites within 10 miles |
| Cerro Gordo | 16 | Soft | 5 sites within 10 miles |
Water quality in Columbus County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Whiteville | City of Whiteville | None detected | 0 lead · 1,283 unknown | 1 |
| Tabor City | Town of Tabor City | Not tested | 0 lead · 42 unknown | None |
| Chadbourn | Town of Chadbourn | Not tested | 0 lead · 78 unknown | 1 |
| Lake Waccamaw | Town of Lake Waccamaw | Not tested | 0 lead · 51 unknown | 1 |
| Brunswick | Town of Brunswick | Not tested | 0 lead · 6 unknown | None |
| Fair Bluff | Town of Fair Bluff | Not tested | 0 lead · 0 unknown | None |
| Sandyfield | Town of Sandyfield | Not tested | 0 lead · 0 unknown | 1 (1 open) |
| Bolton | Town of Bolton | None detected | 0 lead · 445 unknown | 1 |
| Delco | Columbus County Water Dist IV | Not tested | 0 lead · 0 unknown | None |
| Boardman | Town of Boardman | Not tested | 0 lead · 0 unknown | 1 |
| Cerro Gordo | Town of Cerro Gordo | Not tested | 0 lead · 0 unknown | None |
Neighboring counties
- Bladen County22 mg/L
- Brunswick County158 mg/L
- Robeson County18 mg/L
- New Hanover County239 mg/L
- Pender County55 mg/L
- Sampson County32 mg/L
North Carolina
The statewide median is 33 mg/L (soft) from 1,749 sites.
North Carolina hardness map →Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.