Water hardness in Baltimore city, MD

Water in Baltimore city is very hard, with a median of 266 mg/L (15.5 grains per gallon) across 2 monitoring sites.

375% harder than the Maryland median (56 mg/L) 1st hardest of 24 counties
266mg/L
15.5 grains per gallon
Very hard

Baltimore city water at a glance

  • HardnessVery hard (266 mg/L, 15.5 gpg, local measurements). Water softeners are common at this level.Size a water softener →
  • Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →

What 266 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 15.5 gpg (14.9 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites2
Lab samples2
Sample years2000–2003
Middle 50% of sites198–334 mg/L
Groundwater (wells, springs)402 mg/L · 1 sites
Surface water (rivers, lakes)130 mg/L · 1 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Baltimore city

Prefilled with Baltimore city's measured local hardness of 266 mg/L (15.6 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

Baltimore city on the Maryland map

Washington CountyAllegany CountyQueen Anne's CountyCharles CountyAnne Arundel CountyGarrett CountySt. Mary's CountySomerset CountyCaroline CountyWicomico CountyCecil CountyHarford CountyDorchester CountyCalvert CountyBaltimore CountyCarroll CountyFrederick CountyMontgomery CountyWorcester CountyHoward CountyPrince George's CountyKent CountyTalbot County

Cities and communities in Baltimore city

PlaceMedian mg/LClassBased on
Baltimore 266 Very hard 101 sites within 10 miles

Water quality in Baltimore city communities

Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology

CommunityWater systemPFASLead linesViolations
Baltimore City of Baltimore 1 found 47 lead · 335,694 unknown 4

Neighboring counties

Maryland

The statewide median is 56 mg/L (soft) from 1,412 sites.

Maryland hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next