Water hardness in Marysville, WA

Water in Marysville is soft, with a median of 29 mg/L (1.7 grains per gallon) across 31 monitoring sites within 10 miles.

61% softer than the Washington median (74 mg/L) 110th hardest of 122 Washington towns Population 72,916
29mg/L
1.7 grains per gallon
Soft

Marysville tap water at a glance

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 29 mg/L means at home

  • Water softener: A water softener is generally not needed. Soft water rarely causes scale.
  • Dishwasher: set the water hardness to about 1.7 gpg (1.6 °dH), which is the lowest hardness setting (or softener off).
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites31
Lab samples12,477
Sample years2000–2016
Middle 50% of sites24–36 mg/L
Groundwater (wells, springs)89 mg/L · 2 sites
Surface water (rivers, lakes)28 mg/L · 29 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Marysville

Prefilled with Marysville's measured local hardness of 29 mg/L (1.7 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Marysville tap water

Marysville Utilities is the main public water system for Marysville. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 16 samples taken Mar 2023 – Dec 2023. No PFAS were found at or above EPA's minimum reporting levels.

Other water systems serving parts of Marysville

Water systemPFAS detectedHighest PFOA / PFOSTested
Arlington Water Dept
serves over 10,000 people
PFHxS — Feb 2023 – Dec 2023
City of Everett Public Works Dept.
serves over 10,000 people
None detected — Feb 2023 – Nov 2023
Sno Pud 1 - Lake Stevens
serves over 10,000 people
None detected — Jan 2024 – Dec 2024
City of Stanwood Water Dept
serves over 10,000 people
None detected — May 2024 – Nov 2024

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Marysville

Marysville Utilities reported 23,199 service lines (the pipes connecting homes to the water main) in its inventory. It reported no lead or galvanized lines requiring replacement.

0lead (0%)
0galvanized requiring replacement
0unknown material (0%)
23,199not lead (100%)

Other water systems serving parts of Marysville

Water systemService linesTotal
City of Arlington0 lead · 0 galvanized · 983 unknown5,774
City of Everett Public Works Dept.0 lead · 0 galvanized · 0 unknown29,738
Sno Pud 1 - Lake Stevens0 lead · 0 galvanized · 0 unknown21,499
City of Stanwood Water Dept0 lead · 0 galvanized · 1,240 unknown3,159

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Marysville drinking water violations

EPA records show no health-based violations for Marysville Utilities since 2016. It also had 4 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.

Other water systems serving parts of Marysville

Water systemHealth-based violationsMonitoring/reporting
Arlington Water DeptNone0
City of Everett Public Works Dept.None2
Sno Pud 1 - Lake StevensNone2
City of Stanwood Water DeptNone0

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Marysville

SiteTypeDistanceMedianSamplesYears
30N/05E-06Q03 SU-018
USGS Washington Water Science Center
Well 3.4 mi112 mg/L12016
TULALIP CREEK NEAR TULALIP, WA
USGS Washington Water Science Center
Stream 6.2 mi66 mg/L42015
Brenner Creek (Upper)
Stillaguamish Tribe of Indians of Washington (Tribal)
River/Stream 6.9 mi37 mg/L282010–2015
Main Stilly
Stillaguamish Tribe of Indians of Washington (Tribal)
River/Stream 7 mi25 mg/L7192000–2008
Portage Cr @ 80th Ave
Stillaguamish Tribe of Indians of Washington (Tribal)
River/Stream 7.1 mi23 mg/L3852003–2008
Brenner Creek (Lower)
Stillaguamish Tribe of Indians of Washington (Tribal)
River/Stream 7.1 mi37 mg/L282010–2015

Water hardness in towns near Marysville

TownDistanceMedianClass
Lake Stevens6 mi 37 mg/LSoft
Arlington6 mi 36 mg/LSoft
Everett8 mi 66 mg/LModerately hard
Snohomish11 mi 38 mg/LSoft
Eastmont13 mi 70 mg/LModerately hard
Mukilteo13 mi 31 mg/LSoft
Silver Firs15 mi 70 mg/LModerately hard
Mill Creek15 mi 82 mg/LModerately hard
North Lynnwood17 mi 82 mg/LModerately hard
Martha Lake17 mi 88 mg/LModerately hard

Snohomish County

Marysville is in Snohomish County, where the median is 31 mg/L (soft) across 99 sites.

See all of Snohomish County →

Washington

The statewide median is 74 mg/L (moderately hard) from 890 sites.

Washington hardness map →

Marysville, WA water: common questions

Do I need a water softener in Marysville?

Probably not. Water measured around Marysville is 1.7 gpg (29 mg/L, measured locally), under the 7 gpg (120 mg/L) level where scale on fixtures and appliances becomes noticeable.When a softener helps →

Who supplies Marysville's drinking water?

The main public water system serving Marysville in EPA records is Marysville Utilities. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Marysville?

Not for anything in EPA's records: no PFAS found in EPA testing, no lead service lines reported and no health-based violations since 2016. People here who use a filter usually do it for taste, such as chlorine.Chlorine taste in tap water →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next