Water hardness in Burlington, WA
Water in Burlington is soft, with a median of 9 mg/L (0.5 grains per gallon) across Skagit County.
There are not enough monitoring sites within 10 miles of Burlington, so this page uses the Skagit County median.
Burlington tap water at a glance
- HardnessSoft (9 mg/L, 0.5 gpg, local measurements). A water softener isn't needed.Water heater care →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 9 mg/L means at home
- Water softener: A water softener is generally not needed. Soft water rarely causes scale.
- Dishwasher: set the water hardness to about 0.5 gpg (0.5 °dH), which is the lowest hardness setting (or softener off).
- Kettles and coffee makers: descaling every 3–6 months is usually enough.
- Laundry and soap: soap lathers easily and detergent goes further.
- Water heater: routine flushing every 2–3 years is typically fine.
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Burlington
Prefilled with Burlington's measured local hardness of 9 mg/L (0.5 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Burlington tap water
Burlington is served by more than one water system. These systems supply ZIP codes in Burlington and were tested for PFAS ("forever chemicals") in EPA's nationwide UCMR 5 study. Check your water bill to see which one is yours.
Water systems serving Burlington
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| Skagit County Pud 1 Judy Res serves over 10,000 people | PFBA | — | Aug 2024 – May 2025 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Burlington
Burlington is served by more than one water system. Their service line inventories, as reported to EPA:
Water systems serving Burlington
| Water system | Service lines | Total |
|---|---|---|
| Skagit County Pud 1 Judy Res | 0 lead · 5 galvanized · 0 unknown | 26,902 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Burlington drinking water violations
Burlington is served by more than one water system. Health-based violations recorded by EPA since 2016:
Water systems serving Burlington
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| Skagit County Pud 1 Judy Res | None | 2 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Burlington
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| EF NOOKACHAMPS CREEK AT HWY 9 NR CLEAR LAKE, WA USGS Washington Water Science Center | Stream | 3.8 mi | 45 mg/L | 10 | 2015 |
| SAMISH RIVER NEAR BURLINGTON Washington Department Of Ecology | River/Stream | 5.5 mi | 34 mg/L | 6 | 2009–2010 |
Water hardness in towns near Burlington
| Town | Distance | Median | Class |
|---|---|---|---|
| Mount Vernon | 3 mi | 9 mg/L | Soft |
| Sedro-Woolley | 5 mi | 9 mg/L | Soft |
| Anacortes | 14 mi | 9 mg/L | Soft |
| Oak Harbor | 18 mi | 289 mg/L | Very hard |
| Bellingham | 21 mi | 120 mg/L | Hard |
| Arlington | 22 mi | 36 mg/L | Soft |
| Marysville | 28 mi | 29 mg/L | Soft |
| Ferndale | 29 mi | 132 mg/L | Hard |
| Port Townsend | 32 mi | 25 mg/L | Soft |
| Lake Stevens | 34 mi | 37 mg/L | Soft |
Skagit County
Burlington is in Skagit County, where the median is 9 mg/L (soft) across 8 sites.
See all of Skagit County →Washington
The statewide median is 74 mg/L (moderately hard) from 890 sites.
Washington hardness map →Hardness scale
What to read next
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.