Water hardness in Pikesville, MD

Water in Pikesville is very hard, with a median of 237 mg/L (13.8 grains per gallon) across 135 monitoring sites within 10 miles.

323% harder than the Maryland median (56 mg/L) 14th hardest of 121 Maryland towns Population 30,764 (2010)
237mg/L
13.8 grains per gallon
Very hard

Pikesville tap water at a glance

  • HardnessVery hard (237 mg/L, 13.8 gpg, local measurements). Water softeners are common at this level.Size a water softener →

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 237 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 13.8 gpg (13.3 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites135
Lab samples447
Sample years2000–2019
Middle 50% of sites104–282 mg/L
Groundwater (wells, springs)241 mg/L · 111 sites
Surface water (rivers, lakes)155 mg/L · 24 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Pikesville

Prefilled with Pikesville's measured local hardness of 237 mg/L (13.9 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Pikesville tap water

Pikesville is served by more than one water system. These systems supply ZIP codes in Pikesville and were tested for PFAS ("forever chemicals") in EPA's nationwide UCMR 5 study. Check your water bill to see which one is yours.

Water systems serving Pikesville

Water systemPFAS detectedHighest PFOA / PFOSTested
City of Baltimore
serves over 10,000 people
PFPeA — Aug 2024 – May 2025

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Pikesville

Pikesville is served by more than one water system. Their service line inventories, as reported to EPA:

Water systems serving Pikesville

Water systemService linesTotal
City of Baltimore47 lead · 385 galvanized · 335,694 unknown336,126

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Pikesville drinking water violations

Pikesville is served by more than one water system. Health-based violations recorded by EPA since 2016:

Water systems serving Pikesville

Water systemHealth-based violationsMonitoring/reporting
City of Baltimore47

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Pikesville

SiteTypeDistanceMedianSamplesYears
BA Ec 203
USGS Maryland Water Science Center
Well 1.4 mi39 mg/L12000
BA Ec 205
USGS Maryland Water Science Center
Well 2.1 mi237 mg/L12001
BA Dc 462
USGS Maryland Water Science Center
Well 2.2 mi342 mg/L12000
BA Dc 456
USGS Maryland Water Science Center
Well 2.4 mi137 mg/L12000
BA Dc 455
USGS Maryland Water Science Center
Well 2.4 mi138 mg/L12000
BA Dc 447
USGS Maryland Water Science Center
Well 2.5 mi62 mg/L12001

Water hardness in towns near Pikesville

TownDistanceMedianClass
Lochearn3 mi 138 mg/LHard
Mays Chapel4 mi 216 mg/LVery hard
Towson4 mi 244 mg/LVery hard
Milford Mill5 mi 78 mg/LModerately hard
Owings Mills5 mi 76 mg/LModerately hard
Randallstown6 mi 70 mg/LModerately hard
Woodlawn6 mi 103 mg/LModerately hard
Cockeysville7 mi 216 mg/LVery hard
Reisterstown8 mi 78 mg/LModerately hard
Parkville8 mi 258 mg/LVery hard

Baltimore County

Pikesville is in Baltimore County, where the median is 154 mg/L (hard) across 198 sites.

See all of Baltimore County →

Maryland

The statewide median is 56 mg/L (soft) from 1,412 sites.

Maryland hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next