Water hardness in Bellwood, IL

Water in Bellwood is very hard, with a median of 279 mg/L (16.3 grains per gallon) across 12 monitoring sites within 10 miles.

about the same as the Illinois median (293 mg/L) 117th hardest of 225 Illinois towns Population 17,890
279mg/L
16.3 grains per gallon
Very hard

Bellwood tap water at a glance

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 279 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 16.3 gpg (15.6 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites12
Lab samples172
Sample years2000–2017
Middle 50% of sites274–290 mg/L
Groundwater (wells, springs)157 mg/L · 1 sites
Surface water (rivers, lakes)280 mg/L · 11 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Bellwood

Prefilled with Bellwood's measured local hardness of 279 mg/L (16.3 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Bellwood tap water

The City of Bellwood water system is the main public water system for Bellwood. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 4 samples taken Oct 2024 – Feb 2026. No PFAS were found at or above EPA's minimum reporting levels.

Other water systems serving parts of Bellwood

Water systemPFAS detectedHighest PFOA / PFOSTested
Maywood
serves over 10,000 people
None detected — Jun 2024 – Mar 2025
Melrose Park
serves over 10,000 people
None detected — Sep 2023 – Jun 2024

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Bellwood

The City of Bellwood water system reported 2,892 service lines (the pipes connecting homes to the water main) in its inventory. 1,257 are lead and 0 are galvanized lines that must be replaced, and 930 are still of unknown material.

1,257lead (43%)
0galvanized requiring replacement
930unknown material (32%)
705not lead (24%)

EPA's 2024 lead rule requires most water systems to replace these lines within 10 years, starting in November 2027 (the rule is being challenged in court). Ask the City of Bellwood water system whether your address is on its list.

Other water systems serving parts of Bellwood

Water systemService linesTotal
Maywood5,058 lead · 0 galvanized · 0 unknown6,328
Melrose Park744 lead · 0 galvanized · 2,326 unknown5,056

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Bellwood drinking water violations

EPA records show 1 health-based violation for the City of Bellwood water system since 2016, all since resolved or closed. The most recent began in Oct 2024. It also had 4 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.

Contaminant or ruleTypeViolationsMost recentStatus
Lead and Copper Rule Revisions
lead service line inventory and lead rule requirements
Treatment requirement not met 1 Oct 2024 Resolved/closed

Other water systems serving parts of Bellwood

Water systemHealth-based violationsMonitoring/reporting
Maywood1 (1 open)8
Melrose ParkNone1

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Bellwood

SiteTypeDistanceMedianSamplesYears
Addison Creek
illinois epa (State)
River/Stream 0.4 mi306 mg/L242000–2002
ADDISON CREEK AT BELLWOOD, IL
USGS Illinois Water Science Center
Stream 0.4 mi237 mg/L12000
ADDISON CREEK AT 19TH AVENUE AT BROADVIEW, IL
USGS Illinois Water Science Center
Stream 2.5 mi298 mg/L12004
SALT CREEK AT WESTERN SPRINGS, IL
USGS Illinois Water Science Center
Stream 4.2 mi277 mg/L272000–2001
Salt Creek
illinois epa (State)
River/Stream 4.2 mi289 mg/L252000–2002
Des Plaines River
illinois epa (State)
River/Stream 5 mi286 mg/L242000–2002

Water hardness in towns near Bellwood

TownDistanceMedianClass
Melrose Park2 mi 277 mg/LVery hard
Maywood2 mi 286 mg/LVery hard
Westchester2 mi 277 mg/LVery hard
Northlake3 mi 279 mg/LVery hard
River Forest3 mi 286 mg/LVery hard
Forest Park3 mi 283 mg/LVery hard
River Grove3 mi 276 mg/LVery hard
La Grange Park4 mi 277 mg/LVery hard
Elmhurst4 mi 282 mg/LVery hard
Franklin Park4 mi 276 mg/LVery hard

Cook County

Bellwood is in Cook County, where the median is 252 mg/L (very hard) across 63 sites.

See all of Cook County →

Illinois

The statewide median is 293 mg/L (very hard) from 1,100 sites.

Illinois hardness map →

Bellwood, IL water: common questions

Do I need a water softener in Bellwood?

Very likely. Water measured around Bellwood is 16.3 gpg (279 mg/L, measured locally), above 10.5 gpg (180 mg/L), where softeners are common. For a 3-person home that regenerates weekly, that means a softener of about 29,000 grains.Size it for your household →

Who supplies Bellwood's drinking water?

The main public water system serving Bellwood in EPA records is Bellwood. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Bellwood?

It depends on what you want to remove. In Bellwood, the system reports 1,257 lead service lines; if your home has one, a filter certified to remove lead is the usual step until the line is replaced; the system had 1 health-based violation since 2016, for the Lead and Copper Rule Revisions; the utility's annual report says what was done about it. On the other hand, no PFAS found in EPA testing. A water softener is not a filter.Check your own service line →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next