Water hardness in Beaver County, UT

Water in Beaver County is very hard, with a median of 210 mg/L (12.3 grains per gallon) across 234 monitoring sites.

18% softer than the Utah median (256 mg/L) 22nd hardest of 29 counties
210mg/L
12.3 grains per gallon
Very hard

Beaver County water at a glance

  • HardnessVery hard (210 mg/L, 12.3 gpg, local measurements). Water softeners are common at this level.Size a water softener →
  • Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →

What 210 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 12.3 gpg (11.8 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites234
Lab samples751
Sample years2000–2021
Middle 50% of sites132–320 mg/L
Groundwater (wells, springs)226 mg/L · 200 sites
Surface water (rivers, lakes)58 mg/L · 34 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Beaver County

Prefilled with Beaver County's measured local hardness of 210 mg/L (12.3 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

Beaver County on the Utah map

Duchesne CountyCache CountySanpete CountySummit CountySan Juan CountyRich CountyWashington CountyIron CountyJuab CountyCarbon CountyEmery CountyGrand CountyTooele CountyWayne CountyUintah CountyGarfield CountyKane CountyBox Elder CountyMillard CountyWeber CountyWasatch CountyMorgan CountyDavis CountySalt Lake CountyPiute CountyUtah CountySevier CountyDaggett County

Cities and communities in Beaver County

PlaceMedian mg/LClassBased on
Beaver 69 Moderately hard 20 sites within 10 miles
Milford 342 Very hard 33 sites within 10 miles
Minersville 236 Very hard 121 sites within 10 miles

Water quality in Beaver County communities

Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology

CommunityWater systemPFASLead linesViolations
Beaver Beaver City Water System Not tested 0 lead · 0 unknown None
Milford Milford City Water System Not tested 0 lead · 0 unknown None
Minersville Minersville Water System Not tested 0 lead · 151 unknown None

Neighboring counties

Utah

The statewide median is 256 mg/L (very hard) from 4,077 sites.

Utah hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next