Water hardness in Plainview, TX

Water in Plainview is very hard, with a median of 364 mg/L (21.3 grains per gallon) across 3 monitoring sites within 10 miles.

88% harder than the Texas median (194 mg/L) 19th hardest of 251 Texas towns Population 19,420
364mg/L
21.3 grains per gallon
Very hard

Plainview tap water at a glance

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 364 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 21.3 gpg (20.4 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites3
Lab samples3
Sample years2001–2016
Middle 50% of sites342–366 mg/L
Groundwater (wells, springs)364 mg/L · 3 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Plainview

Prefilled with Plainview's measured local hardness of 364 mg/L (21.3 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Plainview tap water

Plainview Municipal Water System is the main public water system for Plainview. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 12 samples taken Jun 2023 – Aug 2024. 1 PFAS was detected.

ChemicalHighest resultDetected inEPA limit
PFBA
perfluorobutanoic acid
5.3 ppt 1 of 12 samples —

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Plainview

Plainview Municipal Water System reported 8,800 service lines (the pipes connecting homes to the water main) in its inventory. 0 are lead and 168 are galvanized lines that must be replaced, and 942 are still of unknown material.

0lead (0%)
168galvanized requiring replacement
942unknown material (11%)
7,690not lead (87%)

EPA's 2024 lead rule requires most water systems to replace these lines within 10 years, starting in November 2027 (the rule is being challenged in court). Ask Plainview Municipal Water System whether your address is on its list.

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Plainview drinking water violations

EPA records show no health-based violations for Plainview Municipal Water System since 2016. It also had 1 monitoring or reporting violation (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Plainview

SiteTypeDistanceMedianSamplesYears
KY-11-51-414
USGS Texas Water Science Center
Well 1.4 mi320 mg/L12016
KY-11-43-805
USGS Texas Water Science Center
Well 6.3 mi364 mg/L12001
KY-11-59-406
USGS Texas Water Science Center
Well 8.6 mi369 mg/L12003

Water hardness in towns near Plainview

TownDistanceMedianClass
Lubbock44 mi 192 mg/LVery hard
Levelland56 mi 449 mg/LVery hard
Canyon56 mi 390 mg/LVery hard
Hereford58 mi 220 mg/LVery hard
Amarillo70 mi 238 mg/LVery hard
Borger103 mi 374 mg/LVery hard
Pampa103 mi 184 mg/LVery hard
Dumas116 mi 223 mg/LVery hard
Big Spring136 mi 512 mg/LVery hard
Andrews138 mi 259 mg/LVery hard

Hale County

Plainview is in Hale County, where the median is 220 mg/L (very hard) across 9 sites.

See all of Hale County →

Texas

The statewide median is 194 mg/L (very hard) from 2,271 sites.

Texas hardness map →

Plainview, TX water: common questions

Do I need a water softener in Plainview?

Very likely. Water measured around Plainview is 21.3 gpg (364 mg/L, measured locally), above 10.5 gpg (180 mg/L), where softeners are common. For a 3-person home that regenerates weekly, that means a softener of about 37,000 grains.Size it for your household →

Who supplies Plainview's drinking water?

The main public water system serving Plainview in EPA records is Plainview Municipal Water System. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →

Do I need a water filter in Plainview?

It depends on what you want to remove. In Plainview, EPA testing found PFBA in the main system; filters certified to NSF/ANSI 53 or 58 for PFOA and PFOS reduction can lower PFAS. On the other hand, no lead service lines reported and no health-based violations since 2016. A water softener is not a filter.Filters that remove PFAS →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next