Water hardness in Stephens County, OK
Water in Stephens County is very hard, with a median of 492 mg/L (28.7 grains per gallon) across 12 monitoring sites.
Stephens County water at a glance
- HardnessVery hard (492 mg/L, 28.7 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 492 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 28.7 gpg (27.6 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Stephens County
Prefilled with Stephens County's measured local hardness of 492 mg/L (28.8 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Stephens County on the Oklahoma map
Cities and communities in Stephens County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Duncan | 484 | Very hard | 9 sites within 10 miles |
| Marlow | 475 | Very hard | 4 sites within 10 miles |
| Comanche | 335 | Very hard | 5 sites within 10 miles |
| Central High | 500 | Very hard | 9 sites within 10 miles |
| Bray | 601 | Very hard | 6 sites within 10 miles |
| Empire City | 500 | Very hard | 11 sites within 10 miles |
| Velma | 492 | Very hard | county median |
| Loco | 492 | Very hard | county median |
| Sunray (CDP) | 335 | Very hard | 3 sites within 10 miles |
Water quality in Stephens County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Duncan | Duncan Public Utilities Authority | 4 found | 0 lead · 10,938 unknown | 44 |
| Marlow | Marlow Municipal Authority | None detected | 0 lead · 0 unknown | 1 |
| Comanche | Comanche Public Works Authority | Not tested | 0 lead · 856 unknown | 54 |
Neighboring counties
- Jefferson County217 mg/L
- Cotton County292 mg/L
- Garvin County406 mg/L
- Carter County277 mg/L
- Grady County585 mg/L
- Comanche County203 mg/L
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.