Water hardness in Custer County, OK
Water in Custer County is very hard, with a median of 1630 mg/L (95.2 grains per gallon) across 23 monitoring sites.
Custer County water at a glance
- HardnessVery hard (1,630 mg/L, 95.2 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →
What 1630 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 95.2 gpg (91.3 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Custer County
Prefilled with Custer County's measured local hardness of 1630 mg/L (95.3 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
Custer County on the Oklahoma map
Cities and communities in Custer County
| Place | Median mg/L | Class | Based on |
|---|---|---|---|
| Weatherford | 670 | Very hard | 3 sites within 10 miles |
| Clinton | 1,675 | Very hard | 16 sites within 10 miles |
| Thomas | 1,630 | Very hard | county median |
| Arapaho | 1,680 | Very hard | 15 sites within 10 miles |
| Custer City | 1,670 | Very hard | 3 sites within 10 miles |
| Butler | 1,640 | Very hard | 9 sites within 10 miles |
Water quality in Custer County communities
Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology
| Community | Water system | PFAS | Lead lines | Violations |
|---|---|---|---|---|
| Weatherford | Weatherford | None detected | 0 lead · 0 unknown | None |
| Clinton | Clinton | 1 found | 0 lead · 4,540 unknown | 5 |
| Thomas | Thomas | Not tested | 0 lead · 0 unknown | None |
| Arapaho | Arapaho | Not tested | 0 lead · 0 unknown | None |
| Custer City | Custer City PWS | Not tested | 2 lead · 188 unknown | None |
| Butler | Butler | Not tested | 0 lead · 0 unknown | None |
Neighboring counties
- Dewey County1688 mg/L
- Washita County1110 mg/L
- Blaine County535 mg/L
- Roger Mills County687 mg/L
- Beckham County702 mg/L
- Caddo County412 mg/L
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.
- Water hardness converterConvert mg/L to grains per gallon or °dH for your dishwasher.
- How to test your well waterFor homes on private wells, which local data doesn't cover.