Water hardness in Mount Washington, KY

Water in Mount Washington is very hard, with a median of 231 mg/L (13.5 grains per gallon) across 3 monitoring sites within 10 miles.

80% harder than the Kentucky median (128 mg/L) 6th hardest of 35 Kentucky towns Population 18,637
231mg/L
13.5 grains per gallon
Very hard

Mount Washington tap water at a glance

  • HardnessVery hard (231 mg/L, 13.5 gpg, local measurements). Water softeners are common at this level.Size a water softener →

Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?

What 231 mg/L means at home

  • Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
  • Dishwasher: set the water hardness to about 13.5 gpg (12.9 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
  • Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
  • Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
  • Water heater: flush the tank once a year to clear sediment and scale.

Where the number comes from

Monitoring sites3
Lab samples115
Sample years2000–2007
Middle 50% of sites212–233 mg/L
Surface water (rivers, lakes)231 mg/L · 3 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Mount Washington

Prefilled with Mount Washington's measured local hardness of 231 mg/L (13.5 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

PFAS in Mount Washington tap water

Mount Washington is served by more than one water system. These systems supply ZIP codes in Mount Washington and were tested for PFAS ("forever chemicals") in EPA's nationwide UCMR 5 study. Check your water bill to see which one is yours.

Water systems serving Mount Washington

Water systemPFAS detectedHighest PFOA / PFOSTested
MT Washington Water Company
serves over 10,000 people
PFOA, PFPeA 7.2 / ND ppt Jun 2025 – Feb 2026
Louisville Water Company
serves over 10,000 people
PFOA, PFPeA, PFHxA +1 more 7.5 / ND ppt Feb 2023 – Nov 2023
North Nelson Water District
serves over 10,000 people
PFOA, PFPeA, PFBS 5.7 / ND ppt Jan 2023 – Oct 2023
Taylorsville Water Works
serves over 10,000 people
PFOA, PFPeA 6.5 / ND ppt May 2025 – Feb 2026

What these PFAS levels mean → Which water filters remove PFAS →

Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology

Lead pipes in Mount Washington

Mount Washington is served by more than one water system. Their service line inventories, as reported to EPA:

Water systems serving Mount Washington

Water systemService linesTotal
MT Washington Water Company0 lead · 0 galvanized · 3,408 unknown11,322
Louisville Water Company483 lead · 2,064 galvanized · 59,521 unknown327,653
North Nelson Water District0 lead · 0 galvanized · 0 unknown5,301
Taylorsville Water Works55 lead · 85 galvanized · 684 unknown9,192

How to tell if your home has a lead pipe → Lead pipes in every state →

As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology

Mount Washington drinking water violations

Mount Washington is served by more than one water system. Health-based violations recorded by EPA since 2016:

Water systems serving Mount Washington

Water systemHealth-based violationsMonitoring/reporting
MT Washington Water CompanyNone5
Louisville Water CompanyNone0
North Nelson Water DistrictNone0
Taylorsville Water WorksNone1

Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology

Monitoring sites closest to Mount Washington

SiteTypeDistanceMedianSamplesYears
COX CREEK NEAR SOLITUDE
Kentucky Division of Water
River/Stream 4.8 mi231 mg/L112004–2005
FLOYDS FORK NEAR SHEPHERDSVILLE
Kentucky Division of Water
River/Stream 5.7 mi235 mg/L512000–2007
SALT RIVER AT SHEPHERDSVILLE
Kentucky Division of Water
River/Stream 9.6 mi193 mg/L532000–2007

Water hardness in towns near Mount Washington

TownDistanceMedianClass
Shepherdsville9 mi 221 mg/LVery hard
Louisville/Jefferson County metro government10 mi 135 mg/LHard
Jeffersontown11 mi 408 mg/LVery hard
St. Matthews15 mi 441 mg/LVery hard
Lyndon15 mi 256 mg/LVery hard
Bardstown16 mi 203 mg/LVery hard
Shively18 mi 467 mg/LVery hard
Shelbyville21 mi 198 mg/LVery hard
Fort Knox25 mi 358 mg/LVery hard
Radcliff26 mi 204 mg/LVery hard

Bullitt County

Mount Washington is in Bullitt County, where the median is 211 mg/L (very hard) across 5 sites.

See all of Bullitt County →

Kentucky

The statewide median is 128 mg/L (hard) from 372 sites.

Kentucky hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next