Water hardness in Melbourne, FL
Water in Melbourne is very hard, with a median of 279 mg/L (16.3 grains per gallon) across 80 monitoring sites within 10 miles.
Melbourne tap water at a glance
- HardnessVery hard (279 mg/L, 16.3 gpg, local measurements). Water softeners are common at this level.Size a water softener →
- PFAS3 found in EPA testing; every result with a federal limit was at or below it.PFAS results →
- Lead pipesNo known lead lines; 28,363 lines are still of unknown material.Check your own pipe →
- ViolationsNo health-based violations since 2016.EPA record →
Choosing a filter? Whole-house vs under-sink · Reverse osmosis · Hot or cold tap water?
What 279 mg/L means at home
- Water softener: Scale build-up is likely. A water softener is commonly used to protect plumbing, water heaters and appliances.
- Dishwasher: set the water hardness to about 16.3 gpg (15.6 °dH), which is a high or maximum hardness setting, with dishwasher salt if your model takes it.
- Kettles and coffee makers: descale every 1–2 months with citric acid or vinegar.
- Laundry and soap: hard water reduces lather, so you may need more detergent, or a softener.
- Water heater: flush the tank once a year to clear sediment and scale.
Size a softener for your home → Hard water and your water heater →
Where the number comes from
Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it
Water softener and dishwasher calculator for Melbourne
Prefilled with Melbourne's measured local hardness of 279 mg/L (16.3 gpg). If your water bill or utility report gives a different number, enter it instead.
Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter
PFAS in Melbourne tap water
City of Melbourne is the main public water system for Melbourne. EPA's nationwide UCMR 5 study tested it for 29 PFAS ("forever chemicals") in 4 samples taken Feb 2023 – Jan 2024. 3 PFAS were detected.
| Chemical | Highest result | Detected in | EPA limit |
|---|---|---|---|
| PFBA perfluorobutanoic acid | 9 ppt | 3 of 4 samples | — |
| PFBS perfluorobutane sulfonic acid | 4 ppt | 3 of 4 samples | — |
| PFPeA perfluoropentanoic acid | 3.1 ppt | 1 of 4 samples | — |
Other water systems serving parts of Melbourne
| Water system | PFAS detected | Highest PFOA / PFOS | Tested |
|---|---|---|---|
| City of Palm Bay serves over 10,000 people | PFOS, PFPeA, PFOA +4 more | 8.5 / 9.5 ppt | Jun 2024 – Jan 2025 |
| West Melbourne WTR SYS(Consec) serves over 10,000 people | PFBA, PFBS, PFPeA | — | Dec 2025 – Jun 2026 |
What these PFAS levels mean → Which water filters remove PFAS →
Highest single sample in parts per trillion (ppt). Limits apply to yearly averages from 2029, so one high sample is not a violation. *Limit proposed for withdrawal in 2026. ND = not detected. PFAS results for every state · Source: EPA UCMR 5 · Methodology
Lead pipes in Melbourne
City of Melbourne reported 60,477 service lines (the pipes connecting homes to the water main) in its inventory. It reported no known lead lines, but 28,363 lines are still of unknown material.
Other water systems serving parts of Melbourne
| Water system | Service lines | Total |
|---|---|---|
| City of Palm Bay | 0 lead · 0 galvanized · 19,375 unknown | 41,838 |
| West Melbourne WTR SYS(Consec) | 0 lead · 1 galvanized · 1,367 unknown | 9,927 |
How to tell if your home has a lead pipe → Lead pipes in every state →
As reported to EPA (first quarter of 2026). Unknown lines may or may not contain lead; numbers change as utilities inspect lines. Sources: EPA service line inventory · EPA Lead and Copper Rule Improvements · Methodology
Melbourne drinking water violations
EPA records show no health-based violations for City of Melbourne since 2016. It also had 2 monitoring or reporting violations (a required test or report was missed or late), which on their own do not mean the water exceeded a limit.
Other water systems serving parts of Melbourne
| Water system | Health-based violations | Monitoring/reporting |
|---|---|---|
| City of Palm Bay | 2 | 0 |
| West Melbourne WTR SYS(Consec) | None | 14 |
Violations since January 2016, EPA records (2026Q3). A violation is not the same as illness; your utility's annual water quality report explains each one. Violations in every state · Source: EPA ECHO / SDWIS · Methodology
Monitoring sites closest to Melbourne
| Site | Type | Distance | Median | Samples | Years |
|---|---|---|---|---|---|
| ELBOW CREEK @ CROTON ROAD FL Dept. of Environmental Protection, Southeast District | Canal Drainage | 0.6 mi | 252 mg/L | 6 | 2003 |
| IRL AT EAU GALLIE RIVER UPSTREAM AT WEIR St. Johns River Water Management District | River/Stream | 1.6 mi | 370 mg/L | 16 | 2014–2016 |
| EAU GALLIE RIVER @ CROTON ROAD FL Dept. of Environmental Protection, Southeast District | River/Stream | 1.6 mi | 318 mg/L | 6 | 2003 |
| EAU GALLIE RIVER @ WICKHAM ROAD FL Dept. of Environmental Protection, Southeast District | River/Stream | 1.7 mi | 367 mg/L | 6 | 2003 |
| ELBOW CREEK @ APOLLO DRIVE FL Dept. of Environmental Protection, Southeast District | River/Stream | 1.7 mi | 120 mg/L | 6 | 2003 |
| CRANE CREEK @ EVANS ROAD FL Dept. of Environmental Protection, Southeast District | River/Stream | 1.8 mi | 350 mg/L | 5 | 2003 |
Water hardness in towns near Melbourne
| Town | Distance | Median | Class |
|---|---|---|---|
| West Melbourne | 4 mi | 282 mg/L | Very hard |
| Satellite Beach | 6 mi | 272 mg/L | Very hard |
| Palm Bay | 10 mi | 296 mg/L | Very hard |
| Viera East | 11 mi | 190 mg/L | Very hard |
| Merritt Island | 14 mi | 282 mg/L | Very hard |
| Cocoa Beach | 15 mi | 234 mg/L | Very hard |
| Rockledge | 15 mi | 239 mg/L | Very hard |
| Cocoa | 19 mi | 242 mg/L | Very hard |
| Cape Canaveral | 20 mi | 250 mg/L | Very hard |
| Sebastian | 25 mi | 316 mg/L | Very hard |
Brevard County
Melbourne is in Brevard County, where the median is 250 mg/L (very hard) across 183 sites.
See all of Brevard County →Melbourne, FL water: common questions
Do I need a water softener in Melbourne?
Very likely. Water measured around Melbourne is 16.3 gpg (279 mg/L, measured locally), above 10.5 gpg (180 mg/L), where softeners are common. For a 3-person home that regenerates weekly, that means a softener of about 29,000 grains.Size it for your household →
Who supplies Melbourne's drinking water?
The main public water system serving Melbourne in EPA records is City of Melbourne. Some neighborhoods may be served by a different system, so check the name on your water bill.How we match towns to water systems →
Do I need a water filter in Melbourne?
It depends on what you want to remove. In Melbourne, EPA testing found PFBA, PFBS and PFPeA in the main system; filters certified to NSF/ANSI 53 or 58 for PFOA and PFOS reduction can lower PFAS. On the other hand, no lead service lines reported and no health-based violations since 2016. A water softener is not a filter.Filters that remove PFAS →
Hardness scale
What to read next
- Do you need a water softener?Water here is very hard; size a softener with our calculator.
- Which water filters remove PFAS?EPA tests found 3 PFAS in Melbourne's main water system.
- How to tell if your home has a lead pipe28,363 service lines here are of unknown material.
- Hard water and your water heaterHow scale affects your water heater and how often to flush.