Water hardness in Pontotoc County, MS

Water in Pontotoc County is soft, with a median of 40 mg/L (2.3 grains per gallon) across 2 monitoring sites.

about the same as the Mississippi median (50 mg/L) 23rd hardest of 73 counties
40mg/L
2.3 grains per gallon
Soft

Pontotoc County water at a glance

  • HardnessSoft (40 mg/L, 2.3 gpg, local measurements). A water softener isn't needed.Water heater care →
  • Private wellsWells aren't covered by public water rules; test yearly for bacteria and nitrate.Well testing →

What 40 mg/L means at home

  • Water softener: A water softener is generally not needed. Soft water rarely causes scale.
  • Dishwasher: set the water hardness to about 2.3 gpg (2.2 °dH), which is the lowest hardness setting (or softener off).
  • Kettles and coffee makers: descaling every 3–6 months is usually enough.
  • Laundry and soap: soap lathers easily and detergent goes further.
  • Water heater: routine flushing every 2–3 years is typically fine.

Where the number comes from

Monitoring sites2
Lab samples2
Sample years2013–2013
Middle 50% of sites29–51 mg/L
Groundwater (wells, springs)40 mg/L · 2 sites

Measured hardness of local source water (mg/L as calcium carbonate) from Water Quality Portal (USGS, EPA and state agencies). Utilities that soften or blend water may deliver different numbers, so check your utility's Consumer Confidence Report for exact tap values. Methodology · On a private well? How to test it

Water softener and dishwasher calculator for Pontotoc County

Prefilled with Pontotoc County's measured local hardness of 40 mg/L (2.3 gpg). If your water bill or utility report gives a different number, enter it instead.

Softener capacity needed (at least)–
Dishwasher setting–set your dishwasher's water hardness to this
Sodium added by softening–

Softener sizes assume the EPA average of 82 gallons per person per day; sodium uses about 8 mg/L added per grain removed (University of Nebraska–Lincoln). More: do you need a softener? · softener salt and sodium · hardness converter

Pontotoc County on the Mississippi map

Panola CountyLauderdale CountyGeorge CountyChickasaw CountyMonroe CountyNoxubee CountyMarion CountyWebster CountyLeake CountyKemper CountyPerry CountySmith CountyClarke CountyLincoln CountyCalhoun CountyQuitman CountyNeshoba CountyFranklin CountyWayne CountyChoctaw CountyStone CountyUnion CountyJefferson Davis CountyAlcorn CountySimpson CountyGrenada CountyWinston CountyBenton CountyLowndes CountyForrest CountyCopiah CountyPrentiss CountyMontgomery CountyWalthall CountyIssaquena CountyNewton CountyHolmes CountyLee CountySharkey CountyAttala CountyTippah CountyLawrence CountyJackson CountyMarshall CountyWarren CountyHancock CountyWashington CountyJones CountyHumphreys CountyOktibbeha CountyScott CountyTate CountyHinds CountyClaiborne CountyClay CountyHarrison CountySunflower CountyMadison CountyJefferson CountyWilkinson CountyPearl River CountyRankin CountyAdams CountyTunica CountyCovington CountyDeSoto CountyGreene CountyLamar CountyLafayette CountyJasper CountyItawamba CountyCarroll CountyBolivar CountyTishomingo CountyCoahoma CountyPike CountyTallahatchie CountyYazoo CountyYalobusha CountyAmite CountyLeflore County

Cities and communities in Pontotoc County

PlaceMedian mg/LClassBased on
Pontotoc 40 Soft county median
Ecru 40 Soft county median
Algoma 40 Soft county median
Thaxton 40 Soft county median
Toccopola 40 Soft county median
Randolph (CDP) 40 Soft county median

Water quality in Pontotoc County communities

Each community's public water system as listed by EPA: PFAS (EPA UCMR 5), lead service lines (EPA inventory) and health-based violations since 2016. Methodology

CommunityWater systemPFASLead linesViolations
Pontotoc City of Pontotoc None detected 0 lead · 0 unknown 1
Ecru Town of Ecru Not tested 0 lead · 0 unknown None

Neighboring counties

Mississippi

The statewide median is 50 mg/L (soft) from 295 sites.

Mississippi hardness map →

Hardness scale

Soft0–60 mg/L0–3.5 gpg
Moderately hard61–120 mg/L3.5–7 gpg
Hard121–180 mg/L7–10.5 gpg
Very hardover 180 mg/Lover 10.5 gpg

What to read next