Dishwasher water hardness setting by brand
Updated November 21, 2026 · Based on the public sources listed below · How we make our content
Short answer: pick your brand below and enter your water hardness. Bosch, Siemens and Neff use settings H00–H07, AEG uses levels 1–10, Fisher & Paykel DishDrawers use 0–5 and Miele takes the hardness itself in °dH. Each comes from the maker's own manual or help page.
Find your setting
Don't know your hardness? Look up your town on the US map or the Canada map; every town page shows it in mg/L and gpg.
Bosch, Siemens and Neff (H00–H07)
| Setting | °E | mmol/l | Range | ≈ mg/L / ppm | ≈ gpg |
|---|---|---|---|---|---|
| H00 | 0–8 | 0–1.1 | Soft | 0–110 | 0.0–6.4 |
| H01 | 9–10 | 1.2–1.4 | Soft | 120–140 | 7.0–8.2 |
| H02 | 11–12 | 1.5–1.8 | Medium | 150–180 | 8.8–10.5 |
| H03 | 13–15 | 1.9–2.1 | Medium | 190–210 | 11.1–12.3 |
| H04 | 16–20 | 2.2–2.9 | Medium | 220–290 | 12.9–16.9 |
| H05 | 21–26 | 3.0–3.7 | Hard | 300–370 | 17.5–21.6 |
| H06 | 27–38 | 3.8–5.4 | Hard | 380–540 | 22.2–31.5 |
| H07 | 39–62 | 5.5–8.9 | Hard | 550–891 | 32.1–52.1 |
Setting, °E, mmol/l and range as printed in the Bosch (SGX78B55UC, SMS6ECI07E), Siemens (SX65ZX07CE) and Neff (S197ZCX08G) manuals, which all use this table (Siemens and Neff write H:00). mg/L and gpg are our conversions.
- Factory setting: H00 on the US Bosch SGX78B55UC; H04 on the European Bosch SMS6ECI07E and the Siemens SX65ZX07CE.
- How to change it (Bosch UK): hold Setup (or SpeedPerfect/VarioSpeed) for 3 seconds, press Start repeatedly until the right value shows, then hold the same button for 3 seconds to save. Bosch notes some models differ.
- Salt: at 0–8 °E Bosch says you can skip dishwasher salt and switch the softener off. Otherwise use special dishwasher salt only.
Miele
Miele has no code: you enter the hardness itself in °dH or mmol/l. The G 7000 manual gives a factory setting of 14 °dH (2.5 mmol/l), a softener range up to 70 °dH, and says no salt is needed if your water is constantly below 5 °dH. If your hardness fluctuates, set the higher value. Change it under Settings → Water hardness.
AEG (levels 1–10)
| Level | °dH | °fH | mmol/l | Clarke | ≈ mg/L |
|---|---|---|---|---|---|
| 1 | <4 | <7 | <0.7 | <5 | under 70 |
| 2 | 4–10 | 7–18 | 0.7–1.8 | 5–12 | 70–180 |
| 3 | 11–14 | 19–25 | 1.9–2.5 | 13–17 | 190–250 |
| 4 | 15–18 | 26–32 | 2.6–3.2 | 18–22 | 260–320 |
| 5 | 19–22 | 33–39 | 3.3–3.9 | 23–27 | 330–390 |
| 6 | 23–28 | 40–50 | 4.0–5.0 | 28–35 | 400–500 |
| 7 | 29–36 | 51–64 | 5.1–6.4 | 36–45 | 510–641 |
| 8 | 37–42 | 65–75 | 6.5–7.5 | 46–52 | 651–751 |
| 9 | 43–46 | 76–83 | 7.6–8.3 | 53–57 | 761–831 |
| 10 | 47–50 | 84–90 | 8.4–9.0 | 58–63 | 841–901 |
From AEG's UK support article; mg/L is our conversion. AEG's factory setting is level 5; at level 1 AEG says not to use salt. On QuickSelect models, hold Quick + ECO for about 3 seconds, choose HAr, change the value and confirm. Other AEG models may differ.
Fisher & Paykel DishDrawer (0–5)
| Setting | ppm | gpg | °dH |
|---|---|---|---|
| 0 | 0–100 | 0–6 | 0–5.6 |
| 1 | 100–250 | 6–14 | 5.6–14 |
| 2 | 250–350 | 14–20 | 14–19.6 |
| 3 | 350–450 | 20–26 | 19.6–25.2 |
| 4 | 450–550 | 26–32 | 25.2–30.8 |
| 5 | 550–625 | 32–36 | 30.8–35 |
From the Fisher & Paykel DishDrawer user guide for the US and Canada (DD24 models). Only some models have a softener. With a household water softener, F&P says to use the setting for water under 100 ppm. Above 625 ppm (36 gpg) wash performance declines and the rinse aid should be set to 5.
Samsung, Whirlpool, Maytag, KitchenAid and GE
- Samsung: the scale is L0–L5 on DW60B models and H1–H6 on others, with level 3 (2.1–3.0 mmol/l) as the default. The menu opens by holding a button pair for 3–5 seconds, depending on the model. Samsung's support page doesn't give a range for each level, so check your manual.
- Whirlpool, Maytag and KitchenAid: on models with a built-in softener, it is off from the factory (setting 0). Hold Hi Temp for 5 seconds, press Start/Resume within 2 seconds, select h, change the value with Normal and confirm with Start/Resume. Then fill the salt reservoir. The help pages don't list the ppm for each value.
- GE (SmartDispense): levels 1–5, set to the number shown on the test strip supplied with the dishwasher. The button combination depends on the control panel.
Not every dishwasher has a hardness setting. If yours doesn't, hard water is handled with the detergent dose and rinse aid. To convert your water report to other units, use the water hardness converter.
Set it too high or too low?
Too low, and hard water minerals can leave a white film on glasses. Too high, and the softener uses more salt; detergent maker Finish also warns that over-softened water can corrode glass. If your glasses are cloudy, see film or etching: how to tell. Hard water also affects washing machines and kettles and fixtures.
Frequently asked questions
What water hardness setting should my dishwasher be on?
Match your local water hardness to your dishwasher's own scale. Bosch, Siemens and Neff use H00–H07, AEG uses levels 1–10, Fisher & Paykel DishDrawers use 0–5, and Miele takes the hardness directly in °dH. If your hardness varies, Miele says to set the higher value.
What setting is my Bosch, Siemens or Neff dishwasher?
All three use the same table in their manuals: for example 1.9–2.1 mmol/l (about 190–210 mg/L) is H03 and 2.2–2.9 mmol/l is H04. Bosch's US manual for the SGX78B55UC lists H00 as the factory setting; the European Bosch and Siemens manuals list H04.
What is the default water hardness level on an AEG dishwasher?
AEG says the default factory setting is level 5, which covers 19–22 °dH (3.3–3.9 mmol/l). At level 1 (under 4 °dH) AEG says not to use salt.
How do I set the water hardness on a Samsung dishwasher?
Samsung's support page lists level 3 (2.1–3.0 mmol/l) as the default. Depending on the model the scale is L0–L5 or H1–H6, set from a button combination held for 3–5 seconds. Samsung's page does not publish a range for every level, so use your model's manual.
Do Whirlpool, Maytag and KitchenAid dishwashers have a water hardness setting?
Models with a built-in water softener do. Their help pages say the softener is off from the factory (setting 0) and is turned on in the setting menu by holding Hi Temp for 5 seconds; then the salt reservoir must be filled with dishwasher softener salt.
Sources
- Bosch use and care manual, SGX78B55UC (US): Overview of water hardness settings
- Bosch information for use, SMS6ECI07E (Europe): Overview of water hardness settings
- Bosch UK: Dishwasher water hardness setting (button steps)
- Siemens information for use, SX65ZX07CE: Overview of water hardness settings
- Neff quick reference guide, S197ZCX08G: Overview of water hardness settings
- Miele operating instructions, G 7130–G 7138: Water hardness, Dishwasher salt
- AEG UK: How to adjust the water hardness level in a dishwasher
- Fisher & Paykel DishDrawer user guide 592816B (US/CA): Water hardness recommendations
- Samsung Canada: White residue on dishes (water hardness levels and steps)
- Whirlpool product help: Water hardness, dishwasher (also Maytag and KitchenAid help pages)
- GE Appliances: SmartDispense, how to set water hardness
- Finish (dishwasher detergent maker): How to wash glassware in the dishwasher